Controlled-products-systems-group 4302-111 Manuale Utente

WARNINGMOVING GATE CAN CAUSEOperate gate only when gate area is in sightand free of people and obstructions.Do not allow children to play in gate area

4302-065-F-1-138Swing Gate Protection Non-contact SensorCDDCSeparate PedestrianWalkwayLocated so pedestrians cannot come in contact with the vehicular

4302-065-F-1-1391.1 Control Box Wiring OverviewSECTION 1 - WIRINGBefore attempting to connect any wiring to the control box, be sure that the circuit

4302-065-F-1-1310Brown WireBlue WireOrange WireRed WireYellow WireGreen WireGreen/Yellow WireNot Used178654321.2 Wiring Operators to 4302 Circuit Boar

4302-065-F-1-13111 2 3 4 5 6 7 8910 11 12 13 14 15 16 17 18 19 20 1.3 Secondary Entrapment Protection WiringClosing-DirectionProtectionClosed GatesOpe

4302-065-F-1-131212345678910 11 121314 1516 17 18 19201.4 Main Terminal DescriptionOperation of the relay is dependent on the setting of SW 2, switche

4302-065-F-1-13131.5 Main Terminal Wiring Key Switch(Dry contact)Keypad(Dry contact)12345678910 11 121314 1516 17 18 1920Controls must be far enough f

4302-065-F-1-1314ReverseReverseShadowAutomatic ExitSecure Side Inside PropertyNon-SecureSide OutsideProperty1.6 Loop Detector WiringLoop detector wiri

4302-065-F-1-13151.7 High Voltage Wiring and Battery ConnectionImportant Power Note: To turn-off ALL power to the operator, the AC power switch must b

4302-065-F-1-13162.1 4302 Circuit Board Description and AdjustmentsSECTION 2 - ADJUSTMENTSThe switch settings and adjustments in this section should b

4302-065-F-1-13172.2 DIP-SwitchesSwitch Function Setting DescriptionOFF1OpeningDirection ofSECONDARYOperator23Terminal #4 is output from plug-in exit

4302-065-F-1-13182.2 DIP-Switches ContinuedSwitch Function Setting DescriptionSW 2 (Bottom 4 Switches)SW 1 Switch Definitions:SW 2 Switch Definitions:

4302-065-F-1-13192.3 Limit Sensors Adjustment - Select your specific operatorThe limit sensors on the operator MUST be adjusted to control the travel

4302-065-F-1-13202.3 Limit Sensors Adjustment ContinuedLimitSlowDownSlow DownLimit6004 Limit Switches ONLYRe-lock operator with release tool and test

4302-065-F-1-1321Cover PlateCLASSCERTIFIED TOCAN/CSA C22.2 NO. 247CONFORMS TOANSI/UL-325VEHICULAR GATE OPERATORHP53382MODELSERIALVOLTSPHASEAMPS60 HzMA

4302-065-F-1-13222.4 Inherent Reverse Sensor AdjustmentThe amount of force required for the gate to reverse direction depends on the reverse sensitivi

4302-065-F-1-1323Under various entrapment conditions the operator will assume either a SOFT or HARD (alarm) shutdown. To determine what type of reset

4302-065-F-1-13242.5 Shutdown Conditions ContinuedHard Shutdown (Alarm Activated)Note: DoorKing operators have a built-in alarm reset push buttons on

4302-065-F-1-1325SECTION 3 - MAINTENANCE AND TROUBLESHOOTING3.1 MaintenanceWhen servicing the gate operator, always check any secondary (external) rev

4302-065-F-1-13263.2 Diagnostics Check Continued4. Check that there are no shorted or open control wires from the keying devices to the gate operator.

4302-065-F-1-13273.3 Troubleshooting ContinuedSymptom Possible Solution(s)Gate closes and opens continuously.Gate starts to close, then reverses to op

4302-065-F-1-131115 VAC CONTROL BOXES SPECIFICATIONSDoorKing, Inc. reserves the right to make changes in the products described in this manual without

4302-065-F-1-1328White Neutral Convenience Outlets 115 VACAC PowerChassisGroundBlack Hot Black Hot White Neutral 115 VAC Standard or Deluxe Control Bo

4302-065-F-1-1329IMPORTANT INFORMATION FOR OWNERStandard Control BoxShut-Off ALL PowerShut-Off ALL PowerShut-Off AlarmShut-Off AlarmDeluxe Control Box

4302-065-F-1-1330Manually Operating the Gate (NO Power)ALL power to the operator must be OFF BEFORE manually operating gate (See previous page).IMPORT

4302-065-F-1-1331

Copyright 2009 DoorKing, Inc. All rights reserved.Use this manual for circuit board 4302-010 Revision A or higher.www.doorking.comDoorKing, Inc.120 Gl

4302-065-F-1-132SPECIFICATIONS 1115 VAC Control Boxes SpecificationsASTM F2200 Standard for Gate ConstructionImportant Safety InstructionsInstructions

4302-065-F-1-133Instructions regarding intended installation: Vehicular gates should be constructed and installed in accordance with ASTM F2200; Stand

4302-065-F-1-134• For gate operators utilizing contact sensors: 1. One or more contact sensors shall be located where the risk of entrapment or ob

4302-065-F-1-135UL 325 Entrapment ProtectionClass IClass I and IIClass IIIClass IVClass IIClass III Class IVA vehicular gate operator (or system) inte

4302-065-F-1-136Glossary GATE - A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone passage b

4302-065-F-1-137Swing Gate Requirements The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a