Controlled-products-systems-group DTG Manuale Utente Pagina 2
- Pagina / 2
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
INSTR,INSTL,DTG
Linear P/N: 211906 B
Material: 20 Lb. Mead Bond
Size 8.500" x 11.000"
Ink: Black
Side 2 of 2
Scale: 1-1
STEP 5
Assemble Cable Grip.
Unscrew the cable grip about 3/4 of the way
and thread the safety edge cable through the cable entry on the transmitter.
STEP 6
Attach Cable.
Attach safety edge cable to terminals as shown.
Tighten cable grip assembly using pliers to assure a water tight seal.
STEP 7
DTG Code Setting.
To set a code, select any valid combination of
ON and OFF positions for the switch keys numbered 1 - 8. Refer to receiver
installation instructions to code receiver switches.
STEP 8
Test Safety Edge.
Test safety edge connection by pressing the
safety edge. The test indicator light should come on.
STEP 9
Wire Receiver.
Wire receiver obstacle output to obstacle input on
operator. Refer to operator and receiver wiring instructions.
STEP 10
Test System.
Activate the gate to close. As the gate is closing, press
the safety edge with your hand. Gate should stop and reverse.
☞
CAUTION! DO not stand in the path of the closing gate.
STEP 11
Replacing Batteries.
If LED indicator fails to light when test button
is pushed, replace with a 9 volt alkaline or lithium battery.
LIMITED WARRANTY
This product is warranted to the consumer against defects in material and workmanship for one year from the date of
purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option, replace, any
device it finds that requires service under this warranty, and will return the repaired or replaced device to the consumer at
the warrantor’s cost. For warranty service and shipping instructions contact warrantor at the address shown below. Devices
must be sent to warrantor for service at owner’s expense. The remedies provided by this warranty are exclusive. Implied
warranties under state law are to the one year period of this written warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. In order to be protected by this warranty, save
your proof of purchase and send copy with equipment should repair be required. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact
Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling.
However, there are some limitations which must be observed.
✶
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As
such, they have limited transmitter power and therefore limited range.
✶
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur
on or near their operating frequencies, regardless of code settings.
✶
Changes or modifications to the device may void FCC compliance.
✶
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
✶
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and
these facts should be communicated to the ultimate users.
Copyright
1999 Linear Corporation 211906 B
C
A
B
L
E
G
R
I
P
A
S
S
E
M
B
LY
TO SAFETY EDGE
ATTACH EDGE SENSOR
CABLE TO TERMINALSTO SAFETY EDGE
O
F
F
O
N
6
5
4
3
2
1
7
8
USE A PAPER CLIP
TO SET THE EIGHT
KEYS
TEST INDICATOR SHOULD
LIGHT WHEN SAFETY EDGE
IS PRESSED
PRESS
WITH
HAND
WARNING!
NO AUTOMATIC
SUPERVISION OF
A DAMAGED GATE
EDGE SENSOR IS
PROVIDED. USER IS
CAUTIONED TO TEST
THE TRANSMITTER
REGULARLY.
PRESS
SAFETY EDGE
CLOSE GATE
GATE OPERATOR
24 V RADIO POWER
RELAY
COMMON
1
2
3
MANUAL ACCESS
REQUEST
DRG
Digital Gate Receiver
OBSTACLE
COMMON
1
2
OBSTACLE INPUT
CHANNEL
ONE
GRAY
YELLOW
CHANNEL
TWO
UNSNAP
BATTERY CLIP
REMOVE BATTERY
FROM HOLDER
WARNING!
NO LOW BATTERY
REPORTS ARE SENT
WHEN THE BATTERY
GETS WEAK. USER IS
CAUTIONED TO TEST
THE TRANSMITTER
MONTHLY.
1
2
Prodotti e manuali riguardandi Hardware Controlled-products-systems-group DTG
(2 pagine)AEG F86460IB manuals
Owner’s manuals and user’s guides for Unknown AEG F86460IB.
We providing 1 pdf manuals AEG F86460IB for download free by document types: User Manual
Commenti su questo manuale